10.8 mm x 6.3 mm x 4.4 mm C8 ferrite block
+/-0.2mm manufacturers tolerance on any dimension Magnetised through the thickness so that one 10.8mm x 6.3mm face is north and the other is south. North pole is painted red These magnets are all new, directly from the manufacturer, however, they have been cut from larger blocks and it is not unusual for the edges to have chips and nibbles or for there to be patches of discolouration. This does not affect the either the power or performance of the magnets.
11.4 mm x 12 mm C5 ceramic ferrite rod / disk
These magnets are all new, directly from the manufacturer, however, they have been cut from a larger block and it is not unusual for the edges to have chips and nibbles or for there to be patches of discolouration. This does not affect the either the power or performance of the magnets Magnetised axially through the thickness so that one 100x25mm face is north and the other is south +/-0.1mm manufacturers cutting tolerance
Manufacturing tolerances: Diameter +/-0.24mm, Thickness +/-0.1mm Magnetised through the thickness so that one flat face is north and the other is south
+/-0.1mm manufacturers tolerance on any dimension Magnetised through the thickness so that one flat face is north and the other is south
120 mm x 20 mm x 15 mm C8 multipolar ceramic ferrite block
+/-0.25mm manufacturing tolerance on any dimension MULTIPOLAR: Each 120x20mm face is magnetised into four alternating poles. The opposite poles appear on the other face.
135mm x 28mm Ferrite Pot Magnet with 57mm steel boss & M14 eyelet bolt
Magnet inside steel cup measures 121mm diameter x 22mm thick +/-0.2mm manufacturers tolerance on any dimension The height of the boss is 30mm with an internal M14 thread The M14 steel eyelet, when screwed into place, is 55mm in height giving a total height of the eyelet and boss of 85mm The eyelet has a 29mm hole for attaching rope. Magnetised axially through the thickness The pull of these magnets was tested in a test rig and will be at LEAST the figure shown The vertical hold is 1/5th of the pull and is, therefore, only for guidance
Manufacturing tolerances: Diameter +/-0.28mm, Thickness +/-0.1mm Magnetised through the thickness so that one flat face is north and the other is south
Manufacturing tolerances: Diameter +/-0.32mm, Thickness +/-0.1mm Magnetised through the thickness so that one flat face is north and the other is south
Manufacturing tolerances: Diameter +/-0.36mm, Thickness +/-0.1mm Magnetised through the thickness so that one flat face is north and the other is south
Manufacturing tolerances: Diameter +/-0.4mm, Thickness +/-0.1mm Magnetised through the thickness so that one flat face is north and the other is south
Ferrite magnet Steel cup with thread Threaded steel hook inserted White powder coated Height of hook to apex 36.76mm
25.4 mm x 6.85 mm C8 ferrite disk
+/-0.1mm manufacturers tolerance on any dimension Magnetised through the thickness so that one flat face is north and the other is south
27 mm x 6.88 mm C8 ferrite disk
+/-0.25mm manufacturers tolerance on any dimension Magnetised through the thickness so that one flat face is north and the other is south
Ferrite magnet Steel cup with thread Threaded steel hook inserted White powder coated Height of hook to apex 35.5mm
C8 20mm x 3mm ferrite disk magnet - craft fridge DIY MRO - PACK OF 50
Technical Specifications Diameter: 20 mm (0.78") Thickness: 3 mm (0.11")Manufacturing tolerances: Diameter +/-0.4mm, Thickness +/-0.1mm Axially Magnetised through the thickness so that one flat face is north, the other is south Weight: 4.6g Grade: C8 (In a size for size comparison, a C8 grade magnet will have approximately 2-3 times more pull than the same size C1 craft magnet.) Coating: None Maximum Temp: 250°C / 482°F Theoretical Maximum Pull: 0.5lb / 8oz / 229g Calculated Max Vertical Hold-guidance only: 0.1lb / 1.6oz / 45g WARNING: We would not recommend this magnet be used by children under 3, and not by children under 5 without supervision - choking hazard and soft tissue pinching hazard.