Guy's Magnets 135mm x 28mm Ferrite Pot Magnet with 57mm steel boss & M14 eyelet bolt

Magnet inside steel cup measures 121mm diameter x 22mm thick +/-0.2mm manufacturers tolerance on any dimension The height of the boss is 30mm with an internal M14 thread The M14 steel eyelet, when screwed into place, is 55mm in height giving a total height of the eyelet and boss of 85mm The eyelet has a 29mm hole for attaching rope. Magnetised axially through the thickness The pull of these magnets was tested in a test rig and will be at LEAST the figure shown The vertical hold is 1/5th of the pull and is, therefore, only for guidance  

Guy's Magnets 18 mm x 3 mm ferrite disk

Manufacturing tolerances: Diameter +/-0.36mm, Thickness +/-0.1mm Magnetised through the thickness so that one flat face is north and the other is south

Guy's Magnets 16 mm x 3 mm ferrite disk

Manufacturing tolerances: Diameter +/-0.32mm, Thickness +/-0.1mm Magnetised through the thickness so that one flat face is north and the other is south

Guy's Magnets 3 mm x 2 mm x 1 mm S1:5 Samarium Cobalt block

+/-0.1mm manufacturers tolerance on any dimension Magnetised through the thickness so that one 3x2mm face is north and the other is south

Guy's Magnets 17.5 mm x 5 mm S2:17 shallow pot

These are specifically designed for press fitting into application and, as such, have no method of anchoring. +/-0.2mm manufacturing tolerances on the steel shell. Diameter of magnet: 14 mm +/-0.2mm Thickness of magnet: 4mm +/-0.5mm THIS IS NOT A TOY, choking hazard. Pull and hold calculations are approximate only are only for guidance.

Guy's Magnets 20 mm x 8 mm x 5 mm PNI8 grade bonded neodymium block

+/- 0.1mm manufacturers tolerance on any dimension Magnetised through the 5mm thickness so that one 20x8mm face is north, the other is south

Guy's Magnets 30 mm x 5 mm C8 ferrite disk

+/-0.25mm manufacturers tolerance on any dimension Magnetised through the thickness so that one flat face is north and the other is south

Guy's Magnets C8 20mm x 3mm ferrite disk magnet - craft fridge DIY MRO - PACK OF 50

Technical Specifications Diameter: 20 mm (0.78") Thickness: 3 mm (0.11")Manufacturing tolerances: Diameter +/-0.4mm, Thickness +/-0.1mm Axially Magnetised through the thickness so that one flat face is north, the other is south Weight: 4.6g Grade: C8 (In a size for size comparison, a C8 grade magnet will have approximately 2-3 times more pull than the same size C1 craft magnet.) Coating: None Maximum Temp: 250°C / 482°F Theoretical Maximum Pull: 0.5lb / 8oz / 229g Calculated Max Vertical Hold-guidance only: 0.1lb / 1.6oz / 45g WARNING: We would not recommend this magnet be used by children under 3, and not by children under 5 without supervision - choking hazard and soft tissue pinching hazard.

Guy's Magnets 2 mm x 4 mm SXG30/20 samarium cobalt rod

+/-0.1mm manufacturers tolerance on any dimension Magnetised through the thickness so that one flat face is north and the other is south

Guy's Magnets 12 mm x 6 mm ferrite disk

+/-0.1mm manufacturers tolerance on any dimension Magnetised through the thickness so that one flat face is north and the other is south

Guy's Magnets 3 mm x 1 mm samarium cobalt disk

+/-0.1mm manufacturers tolerance on any dimension Magnetised through the thickness so that one flat face is north and the other is south

Guys Magnets 20 mm x 3 mm C8 ferrite disk

Manufacturing tolerances: Diameter +/-0.4mm, Thickness +/-0.1mm Magnetised through the thickness so that one flat face is north and the other is south

Guy's Magnets 50mm X 10.5mm Ferrite pot magnet with 8.5mm hole

Magnet inside steel cup measures 45mm outer diameter x 22mm inner diameter x 8mm thick +/-0.2mm manufacturers tolerance on any dimension Magnetised axially through the thickness The pull of these magnets was tested in a test rig and will be at LEAST the figure shown The vertical hold is 1/5th of the pull and is, therefore, only for guidance

Guy's Magnets 14 mm x 3 mm C8 Ferrite disk

Manufacturing tolerances: Diameter +/-0.28mm, Thickness +/-0.1mm Magnetised through the thickness so that one flat face is north and the other is south

Guy's Magnets 25.4 mm x 6.85 mm C8 ferrite disk

+/-0.1mm manufacturers tolerance on any dimension Magnetised through the thickness so that one flat face is north and the other is south

Guy's Magnets 27 mm x 6.88 mm C8 ferrite disk

+/-0.25mm manufacturers tolerance on any dimension Magnetised through the thickness so that one flat face is north and the other is south

Guy's Magnets 25 mm Ferrite Banner Hook

Ferrite magnet Steel cup with thread Threaded steel hook inserted White powder coated Height of hook to apex 36.76mm

Guy's Magnets 32 mm Ferrite Banner Hook

Ferrite magnet Steel cup with thread Threaded steel hook inserted White powder coated Height of hook to apex 35.5mm

Guy's Magnets 3 mm x 5 mm samarium cobalt rod

+/-0.1mm manufacturers tolerance on any dimension Magnetised through the thickness so that one flat face is north and the other is south

Guy's Magnets 4 mm x 20 mm alnico rod

+/-0.1mm manufacturers tolerance on any dimension Magnetised through the thickness so that one flat face is north and the other is south

Guy's Magnets 5 mm x 19 mm alnico rod

+/-0.1mm manufacturers tolerance on any dimension Magnetised through the thickness so that one flat face is north and the other is south

10.8 mm x 6.3 mm x 4.4 mm C8 ferrite block

+/-0.2mm manufacturers tolerance on any dimension Magnetised through the thickness so that one 10.8mm x 6.3mm face is north and the other is south. North pole is painted red These magnets are all new, directly from the manufacturer, however, they have been cut from larger blocks and it is not unusual for the edges to have chips and nibbles or for there to be patches of discolouration. This does not affect the either the power or performance of the magnets.  

Guy's Magnets 12 mm x 3 mm ferrite disk

Manufacturing tolerances: Diameter +/-0.24mm, Thickness +/-0.1mm Magnetised through the thickness so that one flat face is north and the other is south